# The range on the spec sheet

> An inlay datasheet says 15 m. Take off what India allows, a circular antenna, a tilted tag, a full carton and a margin for the room, and you plan for under 3.

- **Page** - https://iotready.com/insights/the-range-on-the-spec-sheet
- **Author** - Tej Pochiraju
- **Published** - 2026-11-05
- **Topics** - Technology, Inventory Management

The datasheet says 15 m. On your floor you'll be lucky to get 5.

Nobody lied to you. Read the small print under the range chart on an inlay datasheet and you'll often find the test power. OSRFID's says "Test power: 4W EIRP" and, a line further down, "For countries that allow 2W ERP, please reduce the result by 11%". That's an honest sheet. It's telling you the number was measured at the American ceiling, with the tag square to the antenna and nothing else about.

The 15 m in the film isn't from any particular datasheet. It's a typical figure for a general-purpose label, and the sums work the same whatever number you start from.

Film: [A 15 m datasheet range losing a few metres to each real loss, down to under 3 m](/media/rfid-06-the-range-on-the-spec-sheet.mp4)

_India's 2 W ERP ceiling, a circular antenna, a tag tilted toward the antenna, a full carton and 6 dB of margin take 15 m to 2.7 m. Each decibel lost costs about 11% of range._

## Which four watts?

This one trips people up.

The FCC limits a UHF reader to 1 W at the antenna port, with an antenna of up to 6 dBi. Use a bigger antenna and the conducted power has to come down by every decibel over 6. So the most an American reader can radiate is 4 W EIRP, 36 dBm. That's the "4 W" on the datasheet.

India's rule has changed. The 2005 RFID rules allowed 1 W from the transmitter and 4 W ERP. G.S.R. 853(E), from December 2021, replaced them: an RFID reader in 865-868 MHz may radiate 2 W ERP, on four 200 kHz channels at 865.7, 866.3, 866.9 and 867.5 MHz. That's Europe's rule (ETSI EN 302 208): the same power on the same four channels. Readers approved under the 2005 rules stay legal until they're retired. 2 W ERP is 35.15 dBm EIRP, because ERP is measured against a dipole and EIRP against an isotropic antenna, 2.15 dB apart.

So the gap between the two ceilings is 0.87 dB. Call it one.

Half the power sounds like a lot, and it costs less than a decibel. Don't compare the 1 W at the port with the 4 W radiated: an American reader puts out 1 W at the port too. Our usual setup, 1 W into 1 dB of cable and a 6 dBi patch, is 35 dBm EIRP. That's just inside India's ceiling and one decibel under the FCC's.

## Then the rest

A circular antenna costs 3 dB against a linear tag. You use one anyway, because the tags arrive at every angle and a linear antenna loses a tag turned 90° altogether.

A tilted tag is two different problems. Twist the tag in the plane facing a circular antenna and you lose nothing more. That's what the circular antenna was for. Tilt it so its antenna points toward the reader and you're off the side of its pattern. A short dipole is down 3 dB at 45°, a half-wave one about 4. The film takes 3.

A full carton detunes the tag. Cardboard and whatever's in the box change what the tag's antenna sees, and the chip gets less of what arrives. The film takes 2 dB. That's a round number, not a measurement. Liquids and metal are a different conversation, and that's the next issue.

Then the room. Floors and racks reflect the signal, and in places the reflections cancel. You don't know where. So you plan with 6 dB in hand, and 10 or more if there's metal or liquid about.

Fifteen decibels. 15 m becomes 2.7.

## Each decibel

In free space, range goes with the square root of power. Every decibel you lose takes about 11% off the range, and every one you gain adds about 12%. Going down it's eleven.

Eleven percent doesn't sound like much. Fifteen of them leave you with 18% of what you started with.

> The datasheet isn't lying. It's the best case, and your floor isn't one.

## What to do with that

Put your own numbers into the [range calculator](https://iotready.com/tools/rfid-range-calculator.md): your tag chip, your reader, your antenna, your margin. It does the sum in the film, and the half the datasheet never mentions, which is whether the reader can hear the tag's reply at all. A cheap reader often runs out of hearing before the tag runs out of power.

If the tag lighting up at all is still a mystery, [Wake the tag](https://iotready.com/tools/wake-the-tag) shows the power link on its own. If you're still choosing the kind of tag, start with [selecting a suitable RFID system](https://iotready.com/insights/selecting-suitable-rfid-system.md).

If you're buying, ask for read range at your power, with your antenna, on your product. If the answer is the datasheet number, nobody has measured it.
