Traceable Quality
Talk to us
Menu

Insight

A cycle count, with a handheld

Part 2 said a 400-carton rack takes about a minute with RFID. Here is that minute, and the two minutes after it that make the count worth trusting.

Part 2 of this series made a promise. A rack of 400 cartons takes twenty minutes with a barcode scanner and about a minute with RFID. That’s true, and it’s the number on every pitch deck. But nobody runs a cycle count to get a number fast. They run it to get a number they can believe.

So here’s the minute, and what comes after it.

A minute of walking, two minutes of checking. Three minutes for the rack, and every gap looked at.

Start with what should be there

Before anyone walks, the handheld needs the list. The IoTReady Mobile App pulls what the system says is on this rack, so the screen starts at 400 expected and 0 counted. Without that list a handheld is just a very fast way of collecting tag numbers. With it, every read is ticked off against something.

Walk the aisle

The reader hears tags through the cardboard, hundreds of them a second, and the count climbs as fast as you walk. That part is as good as it sounds.

Keep the handheld close, though. The 15 metres on a spec sheet is a fixed reader with a big antenna, at full power, with the tag square on and nothing else in the room. On a real floor that’s nearer 5. A handheld has a small antenna and a battery to save, so plan on arm’s length or a little more. Walk both faces of a deep rack, and don’t expect it to hear the back row through a wall of full cartons.

Three missing, one stranger

The minute’s up. 397 of 400, three missing, and one carton the list doesn’t know about.

The useful thing is when you find out. You’re still standing in the aisle. With a barcode count, or with no count at all, a gap like that turns up in next week’s report and somebody has to come back.

Missing means not heard

This is the part the pitch decks skip.

A missing tag hasn’t been proven gone. It just didn’t answer. Maybe the carton was turned round when it was put back and its tag is against the wall. Maybe it’s behind a box of something wet. Maybe the tag is a dud.

So before anyone writes anything off, switch the handheld to locate mode. It’s a Geiger counter for one tag: it beeps faster as you get closer. In the film, one of the three turns up turned round behind its neighbour. The other two really are gone.

The stranger needs the same care. It might be a carton put back on the wrong rack. It might also be a tag on the next rack over that the reader heard through the gap. Check it before you move it, or you’ll “fix” a count that was right.

The sums

By barcode, three seconds a carton is twenty minutes before you chase anything, and you’d have the same three gaps to chase.

By RFID it’s a minute of walking and two minutes of checking four exceptions, at thirty seconds each. Three minutes.

The checking is the bit that makes the number honest. A count that says 397 because one tag faced the wall is wrong by one carton, and a write-off on the strength of it is wrong by one carton’s money. Two minutes is cheap for that.

The minute is the walking. The count you can trust takes three.

Your racks

The cycle-count calculator does these sums for your racks: how many, how big, how often you count them, how many labels are out of reach, and how many cartons are usually out of place. It charges RFID for every tag it didn’t hear, so the answer doesn’t flatter it. For whether RFID suits your stock at all, start with RFID vs barcode vs QR vs BLE. For how far a reader really reaches, there’s the RFID range calculator.

Ten racks like the one in the film, counted every week, is fourteen hours a month by barcode. By RFID it’s two, and every gap in it has been looked at.

Next step

Tell us what you are trying to trace.

Describe the flow: what arrives, what happens to it and what leaves. We will tell you what it takes to capture it.