Traceable Quality
Talk to us
Menu

Free tool

Antenna explorer

Gain narrows the beam. Within the legal power limit it barely lengthens it. Polarisation decides whether a turned tag reads at all. Pick an antenna, turn the tag, and see what each one does to the range.

Plan view from above. The teal wedge is how far the chip wakes inside the antenna's beam. Drag the tag or use the sliders.

Polarisation

0° is a tag lined up with a linear antenna. 90° is crossed.

Beam width
Radiated power
Polarisation loss
Chip wakes out to
Reader hears out to
Range in free space

Free space, a tag facing the antenna, and 1 W into 1 dB of cable, turned down where the antenna would take it past India's 2 W ERP. A real room is usually 30-40% shorter. Wake the tag shows the two links this range comes from; the range calculator lets you change everything.

Which reader

All of these speak the same Gen2 protocol, and most use one of a few reader chips. The antennas and the housing are most of what you're paying for. Cost is rough and relative, not a quote.

TypeAntennasUsed forCost
Handheld1, built inCycle counts, finding one item, receiving at a small site.₹₹₹₹
Fixed reader, 2 or 4 portsUp to 4 patches, your choiceA dock door, a conveyor, a workstation.₹₹₹₹
Fixed reader, 8 ports or more8, or more through a multiplexerSeveral doors or a long shelf run from one box.₹₹₹₹
Portal or gate2 to 4 in a frame, shieldedPallets and trolleys through a doorway.₹₹₹₹
Tunnel4 to 8 inside a metal boxCartons on a conveyor, counted item by item.₹₹₹₹
Overhead arrayMany, steered from the ceilingA whole floor, tags located to a zone.₹₹₹₹
Printer-encoder1, inside the printerWriting the EPC into the label as it prints.₹₹₹₹

The gates and readers we ship are on the RFID hardware page.

A reader is a radio with no speaker. Gain points the same watt in fewer directions. A linear antenna reads a lined-up tag and misses a crossed one; a circular antenna reads at any angle and pays 3 dB for it.

What you’re looking at

A plan view, from above. The antenna sits on the left and throws a beam to the right. The teal wedge is how far the chip wakes anywhere inside the beam, and the dashed edge is how far the reader can still hear the reply. The tag sits on the beam’s centre line; drag it out and it stops reading where the wedge ends.

Gain is the whole story of the wedge. A dipole has 2.15 dBi and hears all round. A 6 dBi patch takes the same watt and points it into a beam about 85 degrees wide, so it reaches further in that direction and nowhere else. Nothing was added. It was pointed.

Then the law steps in. India allows 2 W ERP, about 3.3 W radiated from an isotropic antenna, and 1 W through a 6 dBi patch is already there. Put a 9 dBi panel on the same reader and it has to turn down to about half a watt. The beam gets a little narrower, about 65 degrees, and the chip wakes no further out than it did with the patch. What you gain is on the way back: the panel hears the tag’s reply 3 dB better, which matters when the reader is the weak side.

Then turn the tag. A tag’s antenna is a line, and a linear reader antenna sends a line too. Lined up, nothing is lost. At 45 degrees you’ve lost 3 dB each way. At 60, 6 dB each way, which is half your range. At 90 the two lines are crossed and almost nothing gets through. A circular antenna sends a corkscrew instead. It loses 3 dB against any tag, however it’s turned. That’s why most fixed installations use one.

What it assumes

Free space, a tag facing the antenna, and the same fixed parts as Wake the tag: 1 W into 1 dB of cable, turned down when the antenna would take it past India’s 2 W ERP, 866 MHz, an NXP UCODE 9 chip on a half-wave dipole that reflects a quarter of what reaches it, and an Impinj E710 reader in dense-reader mode. A real room is usually 30-40% shorter.

The beamwidths come from makers’ sheets, rounded: Laird quotes 100 degrees for its 5.5 dBic patch and 70 for its 8.5 dBic panel, FEIG 65 for a 9 dBic panel, Chainway about 40 for a 12 dBi one. Sheets for the same gain differ by 10 or 15 degrees, and the beam is rarely the same width side to side as it is top to bottom. The wedge is the shape of the idea, not a measurement of your antenna. The range calculator lets you change everything else.

Where the numbers come from

Chip and reader sensitivities are NXP’s and Impinj’s own figures, as listed on the range calculator. The power limit is India’s: 2 W ERP for RFID readers in 865-868 MHz, under G.S.R. 853(E) of December 2021, the same figure ETSI EN 302 208 sets for Europe. The polarisation loss is the textbook cos-squared of the angle between two linear antennas, capped at 25 dB because real antennas leak a little across; circular against linear is the standard 3 dB. The reader table is a rough, relative guide to cost, not a quote. The gates and readers we ship are on the RFID hardware page.