Traceable Quality
Talk to us
Menu

Free tool

Cycle-count calculator

Put in your racks and how often you count them. Get the minutes a rack and the hours a month, by barcode and by an RFID handheld, with the exceptions checked.

Your racks

The film's rack is 400 cartons.

A weekly cycle count is 4.

How they sit

Top shelf, turned cartons, shrink-wrap. Each one costs the barcode half a scan more. RFID doesn't care.

Missing or on the wrong rack. Both methods find these and someone has to chase each one. The film's rack has 3 in 400.

Assumptions we started from

Aiming and scanning, label facing out, as in part 2. Generous to the barcode: a full store count by barcode ran at 209 items an hour in the University of Arkansas Bloomingdale's pilot (2009), most of it finding the label.

A handheld walked past a rack of cartons. The walking takes the time; readers hear hundreds of tags a second. Folded stock on a shop floor is slower, about 75 s per 100 in the same pilot.

Tags that are on the rack but didn't answer: turned against metal, behind a full carton, or a dud. RFID flags them as missing until someone checks. The film's rack has 1 in 400.

Walking back, locating the tag or looking for the carton, and deciding. An assumption. Applied to both methods, which is generous to the barcode: it has no locate mode.

Loaded cost of a warehouse operator in India, the same figure as the other RFID tools. Use your own.

One rack

Barcode21.5 min

RFID3 min

12 h a month back, or ₹1,850 of labour.

Where the time goes
BarcodeRFID
Counting one rack20 min60 s
Exceptions to check, per rack34
One rack, exceptions checked21.5 min3 min
Hours a month, every rack14 h2.0 h
Labour a month₹2,150₹300

RFID flags more exceptions than the barcode: the tags it didn't hear on the first pass look missing until someone checks. That checking is the price of a count you can trust, and it's in the table.

The hours are labour only: no tags, no handheld, no software. And they assume the tags read. On metal or liquid, or packed deep, check what a handheld reaches with the RFID range calculator first.

One rack, one handheld. A minute of walking, two minutes of checking what didn't answer. The barcode takes twenty minutes before it chases anything.

What it’s adding up

The barcode time is every item times the seconds a scan takes, with half a scan more for each label you can’t reach. The RFID time is the walk past the rack, which the item count stands in for, because the reader hears hundreds of tags a second and your feet are the slow part.

Then the exceptions. Both methods find the cartons that are really missing or on the wrong rack, and someone has to go and look at each one. RFID also flags the tags it didn’t hear on the first pass: a carton turned round with its tag against the wall, a tag behind a full box. They look missing until someone checks. A handheld’s locate mode makes that quick, but it isn’t free, so the calculator charges RFID for every one.

What it leaves out

It’s labour only. Tags, the handheld, the software and the time to tag the stock in the first place aren’t here.

It also assumes the tags read. A handheld reaches about arm’s length on a real floor, less on metal or liquid, so a deep rack read from one aisle can hide a back row. If your stock is like that, check the range first with the RFID range calculator, and raise “tags not heard on the first pass” until it matches a trial on your own racks.

Where the numbers come from

Three seconds a scan and fifteen seconds per hundred in a sweep are the same starting points as the rest of this series. Three seconds is generous to the barcode: in the University of Arkansas pilot at Bloomingdale’s in 2009, a full store count ran at 209 items an hour by barcode and 4,767 by RFID, because most of a barcode count is finding the label. The exception rates and the thirty seconds to check one are our guesses, set to match the film’s rack. Use yours. For the wider comparison with QR and BLE, see RFID vs barcode vs QR vs BLE, and for the count told as a story, A cycle count, with a handheld.