Traceable Quality®
Talk to us
Menu

Insight

Frequencies, power and borders

The same tag and the same reader wake at 24 m in Chicago and 13 m in Chennai. Power is within a decibel everywhere; the tag is what changes at the border.

A tag that wakes at 24 metres in Chicago wakes at 13 in Chennai.

Same tag. Same reader, same antenna, same chip. The only thing that moved is the frequency, 915 MHz in one place and 866 in the other. The 13 is a model, not a measurement, and I’ll say where it comes from.

UHF RFID is 860 to 960 MHz, but each country opens its own slice. Power is within a decibel everywhere. The tag's tuning is what changes at the border.

Every country opens its own slice

UHF RFID has 100 MHz to play in, from 860 to 960. No regulator opens all of it.

Europe opens 865.6 to 867.6 MHz as four channels of 200 kHz, and a second band at 915 to 921 that only some countries have switched on. India used to be different: its 2005 rule gave RFID 865 to 867 MHz at 1 W. A rule from December 2021, G.S.R. 853(E), replaced that, and India now has the European plan, the same four channels and the same 2 W limit. If you read a guide that says India is 1 W into the antenna, it’s describing the old rule. Readers type-approved under the old one stay legal until they wear out.

The United States takes 902 to 928 MHz and hops across it. To run at 1 W, the rule says you need at least 50 channels and no more than 0.4 seconds on any one of them. China took 920 to 925 in 2024 and closed the old 840 to 845 band to new approvals. Japan, Australia and Brazil each sit near 920. Japan’s licensed high-power band is 916.7 to 920.9, and Australia’s is 920 to 926.

Power is the smaller story

India and Europe both allow 2 W ERP, which is 35.15 dBm radiated. America allows 1 W into an antenna of up to 6 dBi, which is 36 dBm. Australia and Japan’s licensed band land at 36 as well.

That’s under a decibel between the lowest and the highest. A decibel is about 12% of range.

The two rules are written differently, though. India and Europe count what leaves the antenna, so a higher-gain antenna means you turn the reader down. America counts what goes into it, and lets the antenna add its gain up to 6 dBi. If you carry a reader’s settings from one to the other, check which kind of number the setting is.

The tag is where it bites

A tag antenna is cut for a frequency, like a string. Pluck it away from that note and it still rings, quieter.

In the demo I model this crudely: full gain within 8 MHz of the frequency the antenna was cut for, then 0.12 dB lost for every MHz beyond that. A tag cut for 915 MHz and read at 866 is 49 MHz off, which costs 4.9 dB. That’s the 24 metres turning into 13, about 46% of the range gone.

Real inlays differ. Some are cut for the American band, some for the European one, and a global inlay gives up a little peak gain, call it 1 dB, to stay flat across the whole 860 to 960. In the model that same tag in Chennai reads 20 metres instead of 13.

Which is why the advice is dull. If cartons cross borders, ask for global inlays. And if readers sit close together, turn on dense-reader mode so each keeps to its own channel and they stop deafening each other.

What I checked, and what I didn’t

The film and the demo came out of one table of bands and limits, and I read the source for most of it:

  • India: G.S.R. 853(E), 10 December 2021, in the Gazette.
  • Europe: ETSI EN 302 208 V3.3.1, clauses 4.2.2.1 and 4.2.2.2. I could not load the EU decision that opened 915 to 921 MHz, so whether your country has opened it is a question for its regulator.
  • United States: 47 CFR 15.247. The rule limits conducted power; the 4 W EIRP is 1 W plus 6 dBi.
  • Japan: ARIB STD-T106 and T107.
  • Australia: the ACMA class licence, as compiled in 2020. ACMA has remade it since, and I haven’t read the new one.
  • China: I confirmed the 920 to 925 band and the end of 840 to 845 on the CAICT page. The power table (2 W ERP in the middle 4 MHz, 100 mW at the edges) is from a TÜV SÜD summary, not the annex.
  • Brazil: Anatel names the two bands. I did not read the power table, so the demo’s 4 W is a placeholder.

The tag-tuning model is an assumption, and the demo’s 24 and 13 metres are free space with a half-wave dipole tag on an NXP UCODE 9, 3 dB of polarisation loss and the power each region allows. Measure your own inlay on your own bench before you plan around it.

Try your route

Ship from, ship to lets you pick where a carton leaves and where it lands. It draws both bands on one ruler, shows each region’s power, and tells you what a tuned tag and a global one would do at each end. It puts a note on any region I haven’t fully checked, and it should.

For the sums behind the ranges, see the range calculator. For why a tag answers at all, wake the tag.

Before you buy readers for a new country, ask the maker for that country’s variant. It’s one line on the quote.

Next step

Tell us what you are trying to trace.

Describe the flow: what arrives, what happens to it and what leaves. We will tell you what it takes to capture it.