Peel an RFID label off a carton and hold it up to a window. Through the paper you’ll see a silver squiggle with a dot in the middle.
That’s the whole tag. Whatever range and memory you’ve been quoted come out of those two things.
The squiggle and the dot
The squiggle is the antenna. It’s aluminium, about ten microns of it, on a sheet of PET film. The folds are there so an antenna tuned for 866 MHz fits on a label you can stick to a shoebox.
The dot is the chip. Impinj’s M730 is 0.40 by 0.29 millimetres, smaller than a grain of rice by a long way. It has no battery. It runs on what the antenna catches from the reader. Wake the tag covers how that works.
Everything else is packaging. Paper on top makes it a label. A plastic shell makes it a hard tag you can bolt to a crate. A foam spacer holds the antenna off steel so the metal doesn’t kill it. A textile sleeve gets it through an industrial wash. The squiggle changes shape from one to the next, but the job doesn’t.
Four banks
Inside the chip is a small memory. Every chip that speaks Gen2, the protocol UHF readers and tags use, splits it the same four ways.
EPC. This is the number the tag says out loud when a reader asks who’s there. It’s usually 96 bits, which is 24 hex digits. You can rewrite it, and that’s how a roll of blank labels becomes labels for your shirts. It’s also why you lock it afterwards. An open EPC can be overwritten by anyone with a handheld reader.
TID. The chip’s own identity. The first 32 bits say it’s a Gen2 chip, which company made it and which model it is. Then a header word, and on every chip in the table below a 48-bit serial. The Gen2 standard has the maker lock all of it at the factory, so no reader can change it.
That makes the TID the thing to check when you suspect a copy. Anyone can write your EPC onto a blank tag. They can’t give that tag your chip’s serial. But a reader asking “who’s there” only gets the EPC back. Reading the TID is a second command, so if you want the check, you have to ask for it, and you have to have recorded the TID when the tag was first written.
Reserved. Two passwords, 32 bits each. The access password guards the locks: once it’s set, a reader has to know it before it can write to a locked bank or change a lock. The kill password switches the tag off for good. New tags ship with both at zero, and zero means no password. A tag whose kill password is zero can’t be killed at all.
So a tag you lock without setting an access password isn’t really locked. Every reader already knows the password.
And not every chip keeps two. Impinj’s M700 and M800 chips keep one 32-bit password and use it for both jobs. Set it to protect your locks and you’ve also set a kill password, so whoever learns it can switch your tags off. NXP’s UCODE 9 goes the other way: a kill password and no access password, so the only lock that holds on it is a permanent one.
User. Spare room. Plenty of chips don’t have it. The Impinj M730 has none. The M750 has 32 bits. NXP’s UCODE DNA has 3,072. Most deployments leave it empty and keep everything about the item in software, keyed by the EPC. The tag only has to say which item it is.
So which chip?
The chip decides two things you can’t change once the labels are printed.
How far it reads. A chip that wakes at −24 dBm reads further than one that needs −23. One dB sounds like nothing. When waking the chip is what limits the read, it’s about twelve percent more range in free space. The range calculator will show you what it does at your dock door.
How much it remembers. Need a 128-bit EPC? The M750 and the UCODE 9 are out. Need the User bank? Of these four, only the M750 has one, and it holds 32 bits.
| Chip | Wakes at | EPC bank | User bank |
|---|---|---|---|
| Impinj M730 | −24 dBm | 128 bits | none |
| Impinj M750 | −24 dBm | 96 bits | 32 bits |
| NXP UCODE 8 | −23 dBm | 128 bits | none |
| NXP UCODE 9 | −24 dBm | 96 bits | none |
The tag memory map has these and a few more. Pick one, type an EPC and watch the PC word change. Try to write the TID. Set a password, lock the EPC, and see what a stranger’s reader can still do.
Your tag vendor will lead with the label’s size and the adhesive. Ask which chip is inside before any of that. It’s on their datasheet, and if it isn’t, that’s an answer too.